Pine, Klinki

Klinki pine is a Papua New Guinean softwood usually seen as plywood in Australia. It is used for battery separators, ice cream spoons, joinery and furniture.

Other Names

Bulolo Pine, Pai, Rassu, Araucaria klinkii, Wau Pine

Botanical Name

Araucaria hunsteinii

Common Form
Veneer
Species Type

Klinki pine is a timber from New Guinea, usually seen only as plywood in Australia. The wood is virtually identical to hoop pine, but with a lower density. Like hoop pine, the heartwood is a straw to pale brown colour, and the sapwood is not easily distinguishable. The texture is very fine and even, and the grain is straight. Klinki pine can be distinguished from hoop pine by applying a few drops of concentrated hydrochloric acid, which gives the wood an intense green colour. The plywood is used for battery separators, ice-cream spoons and furniture joinery.

Shrinkage

Very Low Low Medium High Very High
Check mark Check mark

Tangential : Provides a simplified rating for tangential shrinkage. This is the measure of the percentage reduction in dimension from the unseasoned to 12% moisture content condition.

2.80%

Radial : Radial shrinkage is perpendicular to the growth rings. It is shrinkage in the direction towards the centre of the tree. Measurement is % value

1.60%

Unit Movement Tangential: This is the percentage of dimensional change for each 1% moisture content change between about 3% moisture content and the fibre saturation point for the particular species.

0.25%

Unit Movement Radial: This is the percentage of dimensional change for each 1% moisture content change between about 3% moisture content and the fibre saturation point for the particular species.

0.16%

Strength Group Strength groups are given for unseasoned (S1-S7) and seasoned (SD1-SD8) timber in accordance with AS 2878. S1 and SD1 yield the highest strength and stiffness whereas S7 and SD8 yield the lowest.

Very High

High

Reasonably High

Medium High

Medium

Reasonably Low

Low

Very Low

Unseasoned:

S1

S2

S3

S4

S5

S6

S7

S8

Check mark

Seasoned:

SD1

SD2

SD3

SD4

SD5

SD6

SD7

SD8

Check mark

Stress Grade A stress grade is defined in AS 1720 as the classification of timber for structural purposes by means of either visual or machine grading. The stress grade indicates the basic working stresses and stiffnesses to be used for structural design purposes. Measured in MPa.

Structural
No. 1
Structural
No. 2
Structural
No. 3
Structural
No. 4
Structural
No. 5

Unseasoned:

F8

F7

F5

F4

Seasoned:

F14

F11

F8

F7

F5

Density per Standard Seasoned density is based on moisture content of 12%. Unseasoned density is an approximation as it depends on the moisture content at the time of measurement. Measured kg/m3.

Seasoned:

430kg/m3

Unseasoned:

470kg/m3

Joint Group The joint group is a classification of the strength of a species in joint design. The values are from 1 (very high strength) to 6 (very low strength).

Very High

High

Reasonably High

Medium

Low

Very Low

Unseasoned:

J1

J2

J3

J4

J5

J6

Check mark

Seasoned:

JD1

JD2

JD3

JD4

JD5

JD6

Check mark

Colour The colour of seasoned heartwood can vary between species and often within a species. The information provided should be used as a general guide only. In most cases, the colour of sapwood is either a lighter shade of the heartwood or a white/cream colour.

  White, yellow, pale straw to light brown Pink to pink brown Light to dark red Brown, chocolate, mottled or streaky
   
Check mark

Mechanical Properties

Modulus of Rupture - Unseasoned: This property is a measure of maximum stress which timber can momentarily sustain when loaded slowly and continuously as a beam. Measured in MPa.

42

Modulus of Rupture - Seasoned: This property is a measure of maximum stress which timber can momentarily sustain when loaded slowly and continuously as a beam. Measured in MPa.

76

Modulus of Elasticity - Unseasoned: This property is of importance in determining the deflection of a beam under load — the greater the stiffness, the less the deflection. Measured in GPa.

10

Modulus of Elasticity - Seasoned: This property is of importance in determining the deflection of a beam under load — the greater the stiffness, the less the deflection. Measured in GPa.

12

Maximum Crushing Strength - Unseasoned:

Also referred to as compression strength. This property measures the ability of the timber to withstand loads applied on the end grain. Measured in MPa.

22

Maximum Crushing Strength - Seasoned: Also referred to as compression strength. This property measures the ability of the timber to withstand loads applied on the end grain. Measured in MPa.

43

Impact - Unseasoned: Provides the Izod value, which is the energy taken in joules (J) to fracture the timber.

10

Impact - Seasoned: Provides the Izod value, which is the energy taken in joules (J) to fracture the timber.

8

Toughness - Unseasoned: This is a measure of timber’s ability to resist shocks and blows, and is synonymous with impact strength. It is measured in Nm.

Low - up to 15 Nm

Toughness - Seasoned: This is a measure of timber’s ability to resist shocks and blows, and is synonymous with impact strength. It is measured in Nm.

Low - up to 15 Nm

Hardness - Unseasoned: Refers to the Janka hardness test and is a measure of timber’s resistance to indentation.

2.0

Hardness - Seasoned: Refers to the Janka hardness test and is a measure of timber’s resistance to indentation.

2.3

Durability

Low Moderate Reasonably High High
(0 - 5 yrs) (5 - 15 yrs) (15 - 25 yrs) (more than 25 yrs)

In-Ground: Durability is defined as the inherent resistance of a timber species to decay, or to insect or marine borer attack. All references to durability refer to the heartwood only. A scale of low to high (durability class 4 = low; 1 = high) has been adapted for above and in-ground durability.

Check mark
(0 - 7 yrs) (7 - 15 yrs) (15 - 40 yrs) (More than 40 yrs)

Above ground: Durability is defined as the inherent resistance of a timber species to decay, or to insect or marine borer attack. All references to durability refer to the heartwood only. A scale of low to high (durability class 4 = low; 1 = high) has been adapted for above and in-ground durability.

(0 - 20 yrs, usually < 5) (21 - 40 yrs) (41 - 64 yrs) (More than 60 yrs)

Marine Borer Resistance: Indicates whether a species is resistant (R) or not resistant (NR) to marine borer attack.

Check mark

Lyctid Borer Susceptibility: Indicates whether a species is susceptible (S) or not susceptible (NS) to lyctid borer attack.

Not Susceptible

Lyctid Borer Susceptibility - Other:

Termite Resistance: Indicates whether a species is resistant (R) or not resistant (NR) to termites.

Not Resistant

Fire Properties

0 1 2 3 4 5 6 7 8 9 10

EFH Spread-of-Flame Index: This is a material's propensity to burn rapidly and spread flames based on a scale of 0 to 10 where 0 means that the materials will not cause flames to reach the ceiling and 10 indicates that the material could be expected to cause flames to reach the ceiling of a room within 10 seconds of ignition.

EFH Smoke-Developed Index:This is a measure of the concentration (measured by optical density) of smoke a material emits as it burns. It is based on an arbitrary scale of 0 to 10. The higher the index, the greater the hazard from smoke is likely to be.

Bushfire Resistance: Naturally bushfire-resisting timbers are those with inherent bushfire-resisting properties. Some species have been tested and a number are in the process of being tested and are measured by Bushfire Attack level (BAL).
BAL -12.5: Ember attack,
BAL – 19: Increasing levels of ember attack and burning debris ignited by windborne embers together with increasing heat flux between 12.5 and 19 kWm3,
BAL – 29: Increasing levels of ember attack and burning debris ignited by windborne embers together with increasing heat flux between 19 and 29 kWm3.

Not Tested
Appearance

Klinki pine is very similar to hoop pine, and can be identified by applying a few drops of hydrochloric acid, which turns the wood an intense green. The texture is very fine and even, and the grain is straight. The sapwood and heartwood are not readily distinguishable, with both being a straw to pale brown colour.

Common Applications

Usually only seen as plywood in Australia, Klinki pine is used for battery separators, ice-cream spoons and furniture joinery. It is also a suitable timber for use in light aircraft.

Workability

Klinki pine is easy to work and very few issues have been encountered.

Origin of timber
SE Asia
Papua New Guinea
Klinki Pine is usually only available as plywood in Australia.

Are you looking for a supplier?

Start Your Search

Social Media Feeds