Stringybark, Brown

Brown stringybark is a moderately durable Australian hardwood, used in general building construction and for fuel.

Other Names

Eucalyptus blaxlandii, Eucalyptus capitellata

Botanical Name

Eucalyptus baxteri

Common Form
Sawn
Species Type
Hardwood
  • Overview

    • Brown stringybark is a hardwood species occurring in coastal and high-rainfall regions of southern New South Wales, Victoria, South Australia and Kangaroo Island. It can grow to heights of up to 40 metres.

    As its trade name suggests, brown stringybark heartwood is pale brown in colour. Its texture is medium and even, with considerable variation in grain. Gum veins are common.

    Brown stringybark timber exhibits moderate strength and durability, and is not recommended for in-ground applications. The sapwood of the species, not always visually distinct from the true wood, is immune to lyctid borer (powder post beetle) attack.

    Although the timber of this species is not especially difficult to work, common applications are limited to general construction, notably building framework, and firewood. 

    Brown stringybark timber products are readily available throughout Victoria, and parts of New South Wales and South Australia.

    Shrinkage

    Very Low Low Medium High Very High
    Check mark Check mark

    Tangential : Provides a simplified rating for tangential shrinkage. This is the measure of the percentage reduction in dimension from the unseasoned to 12% moisture content condition.
    10.40%

    Radial : Radial shrinkage is perpendicular to the growth rings. It is shrinkage in the direction towards the centre of the tree. Measurement is % value
    5.10%

    Unit Movement Tangential: This is the percentage of dimensional change for each 1% moisture content change between about 3% moisture content and the fibre saturation point for the particular species.
    0.33%

    Unit Movement Radial: This is the percentage of dimensional change for each 1% moisture content change between about 3% moisture content and the fibre saturation point for the particular species.
    0.24%

    Strength Group Strength groups are given for unseasoned (S1-S7) and seasoned (SD1-SD8) timber in accordance with AS 2878. S1 and SD1 yield the highest strength and stiffness whereas S7 and SD8 yield the lowest.

    Very High

    High

    Reasonably High

    Medium High

    Medium

    Reasonably Low

    Low

    Very Low

    Unseasoned:

    S1

    S2

    S3

    S4

    S5

    S6

    S7

    S8
    Check mark

    Seasoned:

    SD1

    SD2

    SD3

    SD4

    SD5

    SD6

    SD7

    SD8
    Check mark

    Stress Grade A stress grade is defined in AS 1720 as the classification of timber for structural purposes by means of either visual or machine grading. The stress grade indicates the basic working stresses and stiffnesses to be used for structural design purposes. Measured in MPa.

    Structural
    No. 1    		 Structural
    No. 2    		 Structural
    No. 3    		 Structural
    No. 4    		 Structural
    No. 5

    Unseasoned:

    F17

    F14

    F11

    F8

    F7

    Seasoned:

    F27

    F22

    F17

    F14

    F11

    Density per Standard Seasoned density is based on moisture content of 12%. Unseasoned density is an approximation as it depends on the moisture content at the time of measurement. Measured kg/m3.

    Seasoned:

    840kg/m3

    Unseasoned:

    1150kg/m3

    Joint Group The joint group is a classification of the strength of a species in joint design. The values are from 1 (very high strength) to 6 (very low strength).

    Very High

    High

    Reasonably High

    Medium

    Low

    Very Low

    Unseasoned:

    J1

    J2

    J3

    J4

    J5

    J6
    Check mark

    Seasoned:

    JD1

    JD2

    JD3

    JD4

    JD5

    JD6
    Check mark

    Colour The colour of seasoned heartwood can vary between species and often within a species. The information provided should be used as a general guide only. In most cases, the colour of sapwood is either a lighter shade of the heartwood or a white/cream colour.

      White, yellow, pale straw to light brown Pink to pink brown Light to dark red Brown, chocolate, mottled or streaky
       
    Check mark

    Mechanical Properties

    Modulus of Rupture - Unseasoned: This property is a measure of maximum stress which timber can momentarily sustain when loaded slowly and continuously as a beam. Measured in MPa.
    73

    Modulus of Rupture - Seasoned: This property is a measure of maximum stress which timber can momentarily sustain when loaded slowly and continuously as a beam. Measured in MPa.
    126

    Modulus of Elasticity - Unseasoned: This property is of importance in determining the deflection of a beam under load — the greater the stiffness, the less the deflection. Measured in GPa.
    13

    Modulus of Elasticity - Seasoned: This property is of importance in determining the deflection of a beam under load — the greater the stiffness, the less the deflection. Measured in GPa.
    17

    Maximum Crushing Strength - Unseasoned:

    Also referred to as compression strength. This property measures the ability of the timber to withstand loads applied on the end grain. Measured in MPa.
    39

    Maximum Crushing Strength - Seasoned: Also referred to as compression strength. This property measures the ability of the timber to withstand loads applied on the end grain. Measured in MPa.
    70

    Impact - Unseasoned: Provides the Izod value, which is the energy taken in joules (J) to fracture the timber.
    15

    Impact - Seasoned: Provides the Izod value, which is the energy taken in joules (J) to fracture the timber.
    17

    Toughness - Unseasoned: This is a measure of timber’s ability to resist shocks and blows, and is synonymous with impact strength. It is measured in Nm.
    Medium - 15 - 24 Nm

    Toughness - Seasoned: This is a measure of timber’s ability to resist shocks and blows, and is synonymous with impact strength. It is measured in Nm.
    Medium - 15 - 24 Nm

    Hardness - Unseasoned: Refers to the Janka hardness test and is a measure of timber’s resistance to indentation.
    5.4

    Hardness - Seasoned: Refers to the Janka hardness test and is a measure of timber’s resistance to indentation.
    7.5

    Durability

    Low Moderate Reasonably High High
    (0 - 5 yrs) (5 - 15 yrs) (15 - 25 yrs) (more than 25 yrs)

    In-Ground: Durability is defined as the inherent resistance of a timber species to decay, or to insect or marine borer attack. All references to durability refer to the heartwood only. A scale of low to high (durability class 4 = low; 1 = high) has been adapted for above and in-ground durability.

    		 Check mark
    (0 - 7 yrs) (7 - 15 yrs) (15 - 40 yrs) (More than 40 yrs)

    Above ground: Durability is defined as the inherent resistance of a timber species to decay, or to insect or marine borer attack. All references to durability refer to the heartwood only. A scale of low to high (durability class 4 = low; 1 = high) has been adapted for above and in-ground durability.

    		 Check mark
    (0 - 20 yrs, usually < 5) (21 - 40 yrs) (41 - 64 yrs) (More than 60 yrs)

    Marine Borer Resistance: Indicates whether a species is resistant (R) or not resistant (NR) to marine borer attack.

    		 Check mark

    Lyctid Borer Susceptibility: Indicates whether a species is susceptible (S) or not susceptible (NS) to lyctid borer attack.

    Not Susceptible

    Lyctid Borer Susceptibility - Other:

    Termite Resistance: Indicates whether a species is resistant (R) or not resistant (NR) to termites.

    Not Resistant

    Fire Properties

    Group Number - Other:
    3 if used on MDF or particleboard ≥12mm; veneer thickness 0.6-

    Average Specific Extinction Area: This value is determined by the volume of smoke measured over the mass loss of the tested sample per test carried out in accordance with ‘Cone Calorimeter Test’ AS/NZS 3837. It is measured in units of m2/kg.
    <250

    Bushfire Resistance: Naturally bushfire-resisting timbers are those with inherent bushfire-resisting properties. Some species have been tested and a number are in the process of being tested and are measured by Bushfire Attack level (BAL). BAL -12.5: Ember attack, BAL – 19: Increasing levels of ember attack and burning debris ignited by windborne embers together with increasing heat flux between 12.5 and 19 kWm3, BAL – 29: Increasing levels of ember attack and burning debris ignited by windborne embers together with increasing heat flux between 19 and 29 kWm3.
    BAL 12.5 and 19 – All AS3959 required applications
    Appearance

    The heartwood of this brown stringybark is a pale brown colour. Sapwood may not be clearly defined. Its texture is medium and even with considerable variation in grain. Gum veins are common.

    Common Applications

    Brown stringybark is commonly used for building framework and for fuel.

    Workability

    Brown stringybark is not difficult to work.

    Origin of timber
    NSW
    Readily Available
    NSW
    Brown stringybark is mainly available in Victoria.
    Source of timber
    Native Forest
    a large room with rows of chairs

    Portal Frames

    For buildings that require large spans and column free interiors, timber portal frames provide one of the most aesthetically pleasing solutions. Utilising modern engineering technology, portal frame design transforms timber into a highly effective, efficient and economical structural product.

    Are you looking for a supplier?

    Start Your Search

    Social Media Feeds